Heating of ferromagnetic materials to a temperature above Curie temperature makes it ________________________?

Byadmin February 7, 2019August 20, 2021

Heating of ferromagnetic materials to a temperature above Curie temperature makes it ________________________?

A. Insulator for heat & electricity transmission
B. Ferritic
C. Behave like paramagnetic materials
D. Superconductor

Chemical Engineering Basics

Metallic surveying tapes are made of _____________ which has a low co-efficient of expansion & enough strength ?

Metallic surveying tapes are made of _____________ which has a low co-efficient of expansion & enough strength ?

A. Invar
B. Hastelloy
C. Duralumin
D. Monel metal

Read More Metallic surveying tapes are made of _____________ which has a low co-efficient of expansion & enough strength ?
CHEMICAL ENGINEERING | Chemical Engineering Basics

Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.A. Induced draft fan B. Economiser C. Air preheater D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories ?

Question: Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.A. Induced draft fan B. Economiser C. Air preheater D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories ?
[A].

A, C, B, D
[B].
D, B, C, A
[C].
D, C, B, A
[D].
D, A, B, C

Answer: Option B

Explanation:

No answer description available for this question.

Read More Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.A. Induced draft fan B. Economiser C. Air preheater D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories ?
Chemical Engineering Basics

Identify the correct statement with reference to the extractive metallurgy of aluminium ?

Identify the correct statement with reference to the extractive metallurgy of aluminium ?

A. The electrolyte consists of molten Na3AlF6 with approximately 1 to 8% Al2O3
B. Approximately 80% of the aluminium deposited on the cathode comes from cryolite
C. Sodium is deposited along with aluminium, but is immediately vaporised
D. Anode effect sets in when the cryolite concentration goes below 40%.

Read More Identify the correct statement with reference to the extractive metallurgy of aluminium ?
Chemical Engineering Basics

Suitability of steel for its use in cable is judged by its strength in__________________?

Suitability of steel for its use in cable is judged by its strength in__________________?

A. Tension
B. Compression
C. Torsion
D. Shear

Read More Suitability of steel for its use in cable is judged by its strength in__________________?
Chemical Engineering Basics

The ratio of mass of a neutron to that of an electron is about 1839. What is the ratio of the mass of a proton to that of an electron ?

The ratio of mass of a neutron to that of an electron is about 1839. What is the ratio of the mass of a proton to that of an electron ?

A. 159
B. 1837
C. 2537
D. 10000

Read More The ratio of mass of a neutron to that of an electron is about 1839. What is the ratio of the mass of a proton to that of an electron ?
CHEMICAL ENGINEERING | Chemical Engineering Basics

Area under the stress-strain curve upto the __________ is referred to as the modulus of resilience.

Question: Area under the stress-strain curve upto the __________ is referred to as the modulus of resilience.
[A].

yield strength
[B].
elastic limit
[C].
proportional limit
[D].
maximum point

Answer: Option C

Explanation:

No answer description available for this question.

Read More Area under the stress-strain curve upto the __________ is referred to as the modulus of resilience.

Similar Posts