Chemical Heat Transfer

Evaporation by thermo compression results in the _________________________?

Byadmin March 2, 2019August 24, 2021

Evaporation by thermo compression results in the _________________________?

A. Saving of steam
B. Realisation of multiple effect economy in a single effect
C. Both A. and B.
D. None of these

Chemical Heat Transfer

Leidenfrost point is a term concerned with the____________________?

Leidenfrost point is a term concerned with the____________________?

A. Condensation of the saturated vapor on a cold surface
B. Concentration of a corrosive solution by evaporation
C. Heat transfer between two highly viscous liquids
D. Boiling of a liquid on a hot surface

Read More Leidenfrost point is a term concerned with the____________________?
Chemical Heat Transfer

A 10 cm dia steam pipe, carrying steam at 180°C, is covered with an insulation (conductivity = 0.6 W/m.°C). It losses heat to the surroundings at 30°C. Assume a heat transfer co-efficient of 0.8 W/m2.°C for heat transfer from surface to the surroundings. Neglect wall resistance of the pipe and film resistance of steam. If the insulation thickness is 2 cms, the rate of heat loss from this insulated pipe will be__________________?

A 10 cm dia steam pipe, carrying steam at 180°C, is covered with an insulation (conductivity = 0.6 W/m.°C). It losses heat to the surroundings at 30°C. Assume a heat transfer co-efficient of 0.8 W/m2.°C for heat transfer from surface to the surroundings. Neglect wall resistance of the pipe and film resistance of steam. If the insulation thickness is 2 cms, the rate of heat loss from this insulated pipe will be__________________?

A. Greater than that for un-insulated steam pipe
B. Less than that of the un-insulated steam pipe
C. Equal to that of the un-insulated steam pipe
D. Less than the steam pipe with 5 cms insulation

Read More A 10 cm dia steam pipe, carrying steam at 180°C, is covered with an insulation (conductivity = 0.6 W/m.°C). It losses heat to the surroundings at 30°C. Assume a heat transfer co-efficient of 0.8 W/m2.°C for heat transfer from surface to the surroundings. Neglect wall resistance of the pipe and film resistance of steam. If the insulation thickness is 2 cms, the rate of heat loss from this insulated pipe will be__________________?
Chemical Heat Transfer

A measure of the extent to which viscous heating is important relative to the heat flow resulting from the impressed temperature difference is represented by the _______________ number?

A measure of the extent to which viscous heating is important relative to the heat flow resulting from the impressed temperature difference is represented by the _______________ number?

A. Condensation
B. Grashoff
C. Stanton
D. Brinkman

Read More A measure of the extent to which viscous heating is important relative to the heat flow resulting from the impressed temperature difference is represented by the _______________ number?
Chemical Heat Transfer

Evaporator tubes are generally_____________________?

Evaporator tubes are generally_____________________?

A. Horizontal
B. Vertical
C. Inclined
D. Random

Read More Evaporator tubes are generally_____________________?
Chemical Heat Transfer

Which has the lowest Prandtl number ?

Which has the lowest Prandtl number ?

A. Liquid metal
B. Aqueous solution
C. Water
D. Lube oil

Read More Which has the lowest Prandtl number ?
Chemical Heat Transfer

The rate of heat transfer through a pipe wall is given by, q = 2π k (Ti – T0)/ln (ri/r0). For cylinder of very thin wall, q can be approximated by__________________?

The rate of heat transfer through a pipe wall is given by, q = 2π k (Ti – T0)/ln (ri/r0). For cylinder of very thin wall, q can be approximated by__________________?

A. q = [2π k (Ti + T0)/2]/ln (ri/r0)
B. q = 2π ri k (Ti – T0)/(r0/ri)
C. q = 2π k (Ti – T0)/(r0/ri)
D. q = 2π k (Ti – T0)/[(r0 + ri)/2]

Read More The rate of heat transfer through a pipe wall is given by, q = 2π k (Ti – T0)/ln (ri/r0). For cylinder of very thin wall, q can be approximated by__________________?

Similar Posts