Skip to content
  • Home
  • Contact Us / Report Error
  • Disclaimer

Measurement and Instrumentation

In order to achieve high accuracy, the slide wire of a potentiometer should be_______________?

August 11, 2021December 23, 2018 by admin
In order to achieve high accuracy, the slide wire of a potentiometer should be_______________?

A. as long as possible
B. as short as possible
C. neither too small not too large
D. very thick

Categories Measurement and Instrumentation

A direct current can be measured by________________?

August 11, 2021December 23, 2018 by admin
A direct current can be measured by________________?

A. a D.C. potentiometer directly
B. a D.C. potentiometer in conjunction with a standard resistance
C. a D.C. potentiometer in conjunction with a volt ratio box
D. none of the above

Categories Measurement and Instrumentation

Which of the following devices should be used for accurate measurement of low D.C. voltage ?

August 11, 2021December 23, 2018 by admin
Which of the following devices should be used for accurate measurement of low D.C. voltage ?

A. Small range moving coil voltmeter
B. D.C. potentiometer
C. Small range thermocouple voltmeter
D. None of the above

Categories Measurement and Instrumentation

To measure a resistance with the help of a potentiometer it is_________________?

August 11, 2021December 23, 2018 by admin
To measure a resistance with the help of a potentiometer it is_________________?

A. necessary to standardise the potentiometer
B. not necessary to standardise the potentiometer
C. necessary to use a volt ratio box in conjunction with the potentiometer
D. none of the above

Categories Measurement and Instrumentation

The electrical power to a meggar is provided by________________?

August 11, 2021December 23, 2018 by admin
The electrical power to a meggar is provided by________________?

A. battery
B. permanent magnet D.C. generator
C. AC. generator
D. any of the above

Categories Measurement and Instrumentation

It is required to measure the true open circuit e.m.f. of a battery. The best device is_____________?

August 11, 2021December 23, 2018 by admin
It is required to measure the true open circuit e.m.f. of a battery. The best device is_____________?

A. D.C. voltmeter
B. Ammeter and a known resistance
C. D.C. potentiometer
D. None of the above

Categories Measurement and Instrumentation

An ohmmeter is a____________?

August 11, 2021December 23, 2018 by admin
An ohmmeter is a____________?

A. moving iron instrument
B. moving coil instrument
C. dynamometer instrument
D. none of the above

Categories Measurement and Instrumentation

Murray loop test can be used for location of________________?

August 11, 2021December 23, 2018 by admin
Murray loop test can be used for location of________________?

A. ground fault on a cable
B. short circuit fault on a cable
C. both the ground fault and the short-circuit fault
D. none of the above

Categories Measurement and Instrumentation

In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was___________?

August 11, 2021December 23, 2018 by admin
In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was___________?

A. unity
B. 0.8 lagging
C. 0.8 leading
D. zero

Categories Measurement and Instrumentation

Which of the following is an essential part of a motor meter ?

August 11, 2021December 23, 2018 by admin
Which of the following is an essential part of a motor meter ?

A. An operating torque system
B. A braking device
C. Revolution registering device
D. All of the above

Categories Measurement and Instrumentation
Older posts
Newer posts
← Previous Page1 … Page7 Page8 Page9 … Page11 Next →
© 2025 • Built with GeneratePress