You get a call from a network administrator who tells you that he typed the following into his router:

Byadmin July 24, 2022

Question: You get a call from a network administrator who tells you that he typed the following into his router:

[A].

The wildcard mask is incorrect.

[B].

The OSPF area is wrong.

[C].

The OSPF Process ID is incorrect.

[D].

The AS configuration is wrong.

Answer: Option A

Explanation:

The administrator typed in the wrong wildcard mask configuration. The wildcard should have been 0.0.0.255.

Computer Science | Networking

Which of the following specifies the network address and host address of the computer?

Question: Which of the following specifies the network address and host address of the computer?
[A].

The IP address
[B].
The TCP address
[C].
The subnet mask
[D].
The default gateway

Answer: Option A

Explanation:

No answer description available for this question.

Read More Which of the following specifies the network address and host address of the computer?
Ios And Security Device Manager | Networking

You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?

Question: You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?
[A].

The command requires additional options or parameters.
[B].
There is more than one show command that starts with the letters ru.
[C].
There is no show command that starts with ru.
[D].
The command is being executed from the wrong router mode.

Answer: Option B

Explanation:

The % ambiguous command error means that there is more then one possible command that starts with ru. Use a question mark to find the correct command.

Read More You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?
Eigrp And Ospf | Networking

With which network type will OSPF establish router adjacencies but not perform the DR/BDR election process?

Question: With which network type will OSPF establish router adjacencies but not perform the DR/BDR election process?
[A].

Point-to-point
[B].
Backbone area 0
[C].
Broadcast multi-access
[D].
Non-broadcast multi-access

Answer: Option A

Explanation:

No DR is assigned on any type of point-to-point link. No DR/BDR is assigned on the NBMA point-to-multipoint due to the hub/spoke topology. DR and BDR are elected on broadcast and non-broadcast multi-access networks. Frame Relay is a non-broadcast multi-access (NBMA) network by default.

Read More With which network type will OSPF establish router adjacencies but not perform the DR/BDR election process?
Eigrp And Ospf | Networking

You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information?

Question: You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information?
[A].

show ip eigrp adjacency
[B].
show ip eigrp topology
[C].
show ip eigrp interfaces
[D].
show ip eigrp neighbors

Answer: Option D

Explanation:

The show ip eigrp neighbors command allows you to check the IP addresses as well as the retransmit interval and queue counts for the neighbors that have established an adjacency.

Read More You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information?
Eigrp And Ospf | Networking

A network administrator needs to configure a router with a distance-vector protocol that allows classless routing. Which of the following satisfies those requirements?

Question: A network administrator needs to configure a router with a distance-vector protocol that allows classless routing. Which of the following satisfies those requirements?
[A].

IGRP
[B].
OSPF
[C].
RIPv1
[D].
EIGRP

Answer: Option D

Explanation:

In this question, we’re calling EIGRP just plain old distance vector. EIGRP is an “advanced” distance-vector routing protocol, sometimes called a hybrid routing protocol because it uses the characteristics of both distance-vector and link-state routing protocols.

Read More A network administrator needs to configure a router with a distance-vector protocol that allows classless routing. Which of the following satisfies those requirements?
Eigrp And Ospf | Networking

Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don’t want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?

Question: Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don’t want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?
[A].

router eigrp 11
[B].
router eigrp 10
[C].
router eigrp 10 redistribute igrp
[D].
router igrp combine eigrp 10

Answer: Option B

Explanation:

If you enable EIGRP on a router with the same autonomous system (AS) number, EIGRP will automatically redistribute IGRP into EIGRP. You will see the IGRP injected routes as external (EX) routes with an EIGRP AD of 170. This is a nice feature that lets you migrate slowly to EIGRP with no extra configuration.

Read More Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don’t want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?

Similar Posts